TYT UV8000E USB CABLE HOW TO
TYT UV8000E USB CABLE INSTALL
TYT UV8000E USB CABLE SERIAL
TYT UV8000E USB CABLE DRIVERS

This took me many hours of researching the web and installing/uninstalling all software until I finally got it to work.ДЇor those of you that have this rig, here are the steps required to use the programming software.ДЎ. When it is working correctly, the green light on the top of the radio will flash red as you are transferring data. The plugging in of the radio sequence must be followed all the time or the software will not work correctly. You should now be able to communicate with the radio. No other com port will work for some reason. The software must be assigned in the SETUP to the same com port and it must be com 1 to 4. You find the com port for the cable in Device Manager and clicking on COM/LPT ports. Open the program and set the correct com port. Restart your PC and then load the correct software for the radio.

TYT UV8000E USB CABLE DRIVERS

In Windows go to ADD NEW Hardware Wizard and go through the wizard to load the drivers to the cable. Restart your computer and plug in the cable. You must first load the drivers, then shut down your computer.

There is a definite sequence to this radio and it's software. I am lost except for uninstalling the windows driver and reinstalling the driver that came with the mini CD. It does not matter if I have the USB cable directly plugged into a USB port on the PC or the hub, I still get the same error in that it cannot open the COM port and shuts down any attempt at communicating. The UVF-1 is plugged into a hub on COM 1 and in the software is assigned to COM 6. Using a Dell Inspiron 1200 laptop with Windows XP Home with Service Pack 3 The reason for purchasing this rig was it's dual band capability and I have read good reviews about it and it does work very nicely.

TYT UV8000E USB CABLE HOW TO

I have learned how to program this thing manually and have 6 frequencies programmed. I have checked the web site you showed and I cant see anything about the cable I am using that came with the rig. And seeing that the cable was in the origional box with the rig, I am going to guess that it is not a pirated cable but the correct one to use. The only markings on the USB interface cable is 'USB-02 Cable Programming'. I have emailed the company but they don't answer their emails.

TYT UV8000E USB CABLE INSTALL

I think that I should use the drivers on the CD rather than letting Windows install the driver. It is recognized by my PC and drivers load for it. I believe the cable is a Prolific USB interface. When I purchased this rig all the necessary cables and software were in the box. Prolific is not an END USER cable manufacturer (they are an OEM chip mfg.) - and ONLY recommends TWO cable manufacturers in Taiwan.Д¬ONTACT the Vendor or Dealer where you purchased this cable for resolution or refund, as required. These chips look IDENTICAL - but are not operational. These BAD cables exhibit the problems you are reporting. NOTE: Prolific has announced in December 2011 that counterfeit Prolific chips have been produced in China (mainland) -ДЄnd used in interface cables from China. Since the company is in the same region and heavily promotes their chipsets in that region. USB to UART Bridge IC, such as those from FTDI (UK/EU), Silicon Labs (US), or Prolific (Taiwan).ДЄre you using a USB interface cable? Does this interface cable use Prolific PL-2303 USB chips?Д¬hinese and Eastrern Asian radio manufacturers prefer to use interface cables with the Prolific (Taiwan mfg.) USB chips

The key component in these interface cable is the RS-232 Level Converter, such as the Maxim's MAX-232 or

TYT UV8000E USB CABLE SERIAL

Converts these low voltage levels of the serial data lines to either an RS-232 (DE-9 connector) or Universal Serial Bus (USB) connection for your computer.ДЈ. Provides isolation and protection for your HT internal microprocessors and components from your computer or external voltages/signals.Дў. The interface cable is important, because:ДЎ. In order for these radios to 'talk' to your personal computer - an interface cable is required. The digital signals from these processors and support ICs operate at TTL levels (voltages of 5, 3.3, or 1.67 Volts). Modern Amateur Radio mobile radios and hand-held radios (HTs) are micro-processor controlled.

Click to expand.TYT Electronics Co., Ltd.ДЄddress: Block 39-1, Optoelectronics-information industry base, NanвЂ™an, quanzhou, Fujian (CHINA)

Tyt uv8000e usb cable